Just Bolt the Pumps on Direct!
Aquatech-USA offers the highest quality replacement pressure washer pumps that are available in the marketplace. These pumps are so reliable that they come with an industry leading warranty coverage up to 7 years. Our following pump replacement kits are completely assembled and ready to go. It’s easy, just remove your old pump from the gasoline engine and bolt on the new one. It’s that simple and the pumps are made ready to replace the cheap cast aluminum head pumps that come on many of the box store and catalog pressure washers.
Aquatech-USA pumps also come equipped with downstream detergent injectors, so that you can incorporate different detergents to give you that extra boost for all your cleaning needs.
Giant brand pumps
The Giant brand pumps that Aquatech-USA offer are built and made here in the USA, keeping American workers employed and your well spent dollars in the USA. The Giant pumps are built with brass heads and stainless-steel plungers making them an upgrade to the all-aluminum pumps that most consumer pressure washer come equipped with.
Comet brand pumps
The Comet brand pumps that Aquatech-USA offer come with triple length bypass hoses and external unloader valves to extend the amount of time that you can run your pressure washer in bypass and for easy troubleshooting and inexpensive repairs down the road.
How Aquatech-USA differs
Each of our pumps come standard with thermal relief valves to protect the life of the pump seals that can be damaged if the pump is left in bypass for a period creating friction heat within the pump head. Therefore, the thermal relief valve will expel any hot water that builds up while in bypass then reset the valve and allow fresh cooler water into the head keeping the seals out of the temperature danger zone.
All the pumps offered by Aquatech-USA have oil bath crankcases with fill and drain ports. The oil bath crankcases keep the pump internal parts cool and lubricated, especially under the high speed that they operate, assuring you many years of trouble free use. Surprisingly, some of the competitive and cheap brand pumps have gone to completely sealed crankcases where the lubricant cannot be changed or even oil less pumps that have a short lifetime to them until they overheat and break apart within a few years of operation.
Changing out a damaged or worn out power washer pump can be a more economical way to upgrade your pressure washer then going out and replacing it with a completely new unit. Moreover, when you repair your pressure washer versus throwing it away and buying a new one it is actually more environmentally friendly because you are kept from discarding old gasoline engines, plastic parts, rubber wheels and broken metal frames into the landfills. Aquatech-USA can even help you discard your old pump and pump oil by partnering with local recycle centers at no cost to you, keeping your pump purchase a “Green” experience.
Why Aquatech-USA
You will find that Aquatech-USA pumps are very affordable when you consider the quality, dependability, warranty, ease of installation, eco-friendly and variety of standard accessories that makes Aquatech-USA the pressure washer leader that you can rely upon. In other words, we want help assist you in any way to make sure you choose the right pump for your application, so please contact one of our sales staff via phone at 1-800-564-6879 or at Aquatech-USA.
GIANT GX2525VA $230.00
- 7/8″ Vertical Shaft (perfect for short shaft engines)
- 4-7HP
- 5 GPM
- 2500 PSI max
- 3400 RPM max
- Gas Engine
- Built In Unloader
- MADE IN USA
- 1 year warranty against manufacture defects
2500 PSI, 2.5 GPM Giant Direct Drive Pump Assembly W/ Built In Unloader. This pump has all the necessary components to make installation a breeze!!
PUMP:
• Giant GX2525VA Wobble Plate Plunger Pump
• Direct Drive with Gas Flange 4.0-7.0 HP SAE
• Max. Volume: 2.5 GPM
• Max. Discharge Pressure: 2,500 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 7/8” Hollow
• Max. Horsepower Requirements: 7.0 GHP
• Max. Fluid Temp.: 80º F
• Drive Side: Either side
• Forged brass head & valve covers
• Solid ceramic oxide plungers
COMPONENTS:
• Giant GX2525VA Wobble Plate Plunger Pump
• Built In adjustable pressure unloader with thermal relief valve and detergent injector
• ¾” female brass garden hose swivel inlet with screened gasket
• 3/8” Quick connect stainless steel coupler
• Mounting bracket
• Mounting bolts
• Weight: 9.0 lbs.
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
GIANT GX2525HA $250
- 3/4″ Horizontal Shaft (perfect for short shaft engines)
- 5-7HP
- 5 GPM
- 2500 PSI max
- 3400 RPM max
- Gas Engine
- Built In Unloader
- MADE IN USA
- 1 year warranty against manufacture defects
2500 PSI, 2.5 GPM Giant Direct Drive Pump Assembly W/ Built In Unloader. This pump has all the necessary components to make installation a breeze!!
PUMP:
• Giant GX2525HA Wobble Plate Plunger Pump
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 2.5 GPM
• Max. Discharge Pressure: 2,500 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 7.0 GHP
• Max. Fluid Temp.: 80º F
• Drive Side: Either side
• Forged brass head & valve covers
• Solid ceramic oxide plungers
COMPONENTS:
• Giant GX2525HA Wobble Plate Plunger Pump
• Built In adjustable pressure unloader with thermal relief valve and detergent injector
• ¾” female brass garden hose swivel inlet with screened gasket
• 3/8” Quick connect stainless steel coupler
• Mounting bracket
• Mounting bolts
• Weight: 9.0 lbs.
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
COMET BXD2530GE $335
- 3/4″ Horizontal Shaft
- 5-7HP
- 5 GPM
- 3000 PSI max
- 3400 RPM max
- Gas Engine
- Built In Unloader
- MADE IN ITALY
- 2 year warranty against manufacture defects
2500 PSI, 2.5 GPM Comet Direct Drive Pump Assembly W/ Built In Unloader. This pump has all the necessary components to make installation a breeze!!
PUMP:
• Comet BXD2530GE Cam Axial Pump
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 2.5 GPM
• Max. Discharge Pressure: 3,000 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 7.0 GHP
• Max. Fluid Temp.: 120º F
• Drive Side: Either side
• Forged brass head & valve covers
• Solid ceramic oxide plungers
COMPONENTS:
• Comet BXD2530GE Cam Axial Pump
• Built In adjustable pressure unloader with thermal relief valve and detergent injector
• ¾” female brass garden hose swivel inlet with screened gasket
• 3/8” Quick connect brass coupler
• Weight: 10.3 lbs.
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted.
COMET LWD3025GE $596
- 3/4″ Shaft
- 5 – 7 HP
- 0 GPM
- 2500 PSI
- 3400 RPM
- Gas Engine
- External Unloader
- MADE IN ITALY
- 7 year warranty against manufacture defects
2500 PSI, 3.0 GPM Comet Direct Drive Pump Assembly W/ VR54 Unloader. This pump has all the necessary components to make installation a breeze!!
PUMP:
• Comet LWD3025GE Triplex Plunger Pump
• Direct Drive with Gas Flange 5.5-7.0 HP SAE
• Max. Volume: 3.0 GPM
• Max. Discharge Pressure: 2,500 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 7.0 GHP
• Max. Fluid Temp.: 145º F
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
COMPONENTS:
• Comet LWD3025GE Triplex Plunger Pump
• Mecline VR54 adjustable pressure unloader with thermal relief valve & detergent injector
• Black bypass hose triple length
• Brass Line Strainer w/ Cone Filter, GH Inlet
• 3/8” QC brass socket
• 2 Brass push-on hose fittings
• Mounting bolts
• Weight: 15.0 lb
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
COMET ZWD4040GE $741
- 1″ Shaft
- 8-15 HP
- 0 GPM
- 4000 PSI
- 3400 RPM
- Gas Engine
- External Unloader
- MADE IN ITALY
- 7 year warranty against manufacture defects
4000 PSI, 4.0 GPM Comet Direct Drive Pump Assembly W/ VRT3 EZ Start Unloader. This pump has all the necessary components to make installation a breeze!!
PUMP:
• Comet ZWD4040GE Triplex Plunger Pump
• Direct Drive with Gas Flange 9.0-13.0 HP SAE
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.5 GHP
• Max. Fluid Temp.: 145º F
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
COMPONENTS:
• Comet ZWD4040GE Triplex Plunger Pump
• Mecline VRT3 EZ Start adjustable pressure unloader with thermal relief valve
• Black bypass hose triple length
• Brass Line Strainer w/ Cone Filter, GH Inlet
• 3/8” QC brass socket
• 2 Brass push-on hose fittings
• Mounting bolts
• Weight: 20.75 lb
• Note: Pumps are sometimes not fully assembled for shipping purposes or tested prior to shipping and unloader will need to be adjusted
Leave a reply